External Flash Units

Use optional external flash units for flash photography. Some units support high-speed sync (FP) and can be used at shutter speeds faster than the flash sync speed, while others can function as master flash units controlling remote units via optical wireless flash control.

You may be unable to test-fire the flash in some circumstances, for example when camera menus are displayed.

Red-Eye Removal

Red-eye removal is available when an option other than [OFF] is selected for F[FLASH SETTING] > [RED EYE REMOVAL] and G [AF/MF SETTING] > [FACE/EYE DETECTION SETTING] is [FACE DETECTION ON]. Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s retinas.

Flash Sync Speed

The flash will synchronize with the shutter at shutter speeds of 1/250 s or slower.

Optional Flash Units from Fujifilm

The camera can be used with optional Fujifilm shoe-mounted flash units.

Third-Party Flash Units

Do not use third-party flash units that apply over 300 V to the camera hot shoe.

Using an External Flash
[EF-X8]
[SYNC TERMINAL]
[SHOE MOUNT FLASH]
[MASTER (OPTICAL)]

Using an External Flash

To adjust settings for a flash unit mounted on the hot shoe or connected via the sync terminal:

Connect the unit to the camera.

In shooting mode, select [FLASH FUNCTION SETTING] in the F ([FLASH SETTING]) menu tab. The options available vary with the flash unit.

Menu	Description
[EF-X8]	Displayed when an optional EF-X8 flash unit is mounted on the hot shoe and raised (a[EF-X8]).
[SYNC TERMINAL]	Adjust settings for flash units connected via the sync terminal. [SYNC TERMINAL] is displayed if the EF-X8 is lowered and either no flash unit, or an incompatible flash unit, is mounted on the hot shoe (a[SYNC TERMINAL]).
[SHOE MOUNT FLASH]	Displayed when an optional flash unit other than the EF-X8 is mounted on the hot shoe and turned on (a[SHOE MOUNT FLASH]).
[MASTER (OPTICAL)]	Displayed if an optional flash unit functioning as a master flash for Fujifilm optical wireless remote flash control is connected and turned on (a[MASTER (OPTICAL)]).

Highlight items using the selector and rotate the rear command dial to change the highlighted setting.
Press [DISP/BACK] to put the changes into effect.

[EF-X8]

The following settings are available when an optional EF-X8 shoe-mounted flash unit is attached.

Setting	Description
AFlash control mode	Choose from the following options: [TTL]: TTL mode. Adjust flash compensation (B) and choose a flash mode (C). [M]: The flash fires at the selected output (B) regardless of subject brightness or camera settings. Output is expressed in fractions of full power, from 1/1 to 1/64. The desired results may not be achieved at low values if they exceed the limits of the flash control system; take a test shot and check the results. C ([COMMANDER]): Choose if the flash is being used to control remote synced flash units, for example as part of a studio flash system. D: The EF-X8 does not fire. Flash units connected via the sync terminal will still fire when the shutter is released, but can be disabled by lowering the EF-X8 and turning the units off in the flash settings menu.
BFlash compensation/output	Adjust flash level. The options available vary with the flash control mode (A).
CFlash mode (TTL)	Choose a flash mode for TTL flash control. The options available vary with the shooting mode ([P], [S], [A], or [M]) selected. E ([FLASH AUTO]): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken. F ([STANDARD]): The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released. G ([SLOW SYNC.]): Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.
DSync	Choose whether the flash is timed to fire immediately after the shutter opens (H/[1ST CURTAIN]) or immediately before it closes (I/[2ND CURTAIN]). [1ST CURTAIN] is recommended in most circumstances.

[SYNC TERMINAL]

Displayed when no compatible flash unit is connected.

Setting	Description
AFlash control mode	Choose from the following options: [M]: A trigger signal is transmitted via the hot shoe X contacts when a picture is taken. Choose a shutter speed slower than the sync speed; even slower speeds may be required if the unit uses long flashes or has a slow response time. D: The trigger signal is disabled.
BSync	Choose whether the flash is timed to fire immediately after the shutter opens (H/[1ST CURTAIN]) or immediately before it closes (I/[2ND CURTAIN]). [1ST CURTAIN] is recommended in most circumstances.

Setting

Description

AFlash control mode

Choose from the following options:

[M]: A trigger signal is transmitted via the hot shoe X contacts when a picture is taken. Choose a shutter speed slower than the sync speed; even slower speeds may be required if the unit uses long flashes or has a slow response time.
D: The trigger signal is disabled.

BSync

Choose whether the flash is timed to fire immediately after the shutter opens (H/[1ST CURTAIN]) or immediately before it closes (I/[2ND CURTAIN]). [1ST CURTAIN] is recommended in most circumstances.

The Sync Terminal

Use the sync terminal to connect flash units that require a sync cable.

[SHOE MOUNT FLASH]

The following options are available when an optional shoe-mounted flash unit is attached and turned on.

Setting	Description
AFlash control mode	The flash control mode selected with the flash unit. This can in some cases be adjusted from the camera; the options available vary with the flash. [TTL]: TTL mode. Adjust flash compensation (A). [M]: The flash fires at the selected output regardless of subject brightness or camera settings. Output in some cases can be adjusted from the camera (B). [MULTI]: Repeating flash. Compatible shoe-mounted flash units will fire multiple times with each shot. D: The flash does not fire. Some flash units can be turned off from the camera.
BFlash compensation/output	The options available vary with flash control mode. [TTL]: Adjust flash compensation (the full value may not be applied if the limits of the flash control system are exceeded). In the cases of the EF-X20, EF-20, and EF-42, the selected value is added to the value selected with the flash unit. [M]/[MULTI]: Adjust flash output (compatible units only). Choose from values expressed as fractions of full power, from 1/1 (mode [M]) or 1/4 ([MULTI]) down to 1/512 in increments equivalent to 1/3 EV. The desired results may not be achieved at low values if they exceed the limits of the flash control system; take a test shot and check the results.
CFlash mode (TTL)	Choose a flash mode for TTL flash control. The options available vary with the shooting mode ([P], [S], [A], or [M]) selected. E([FLASH AUTO]): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken. F([STANDARD]): The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released. G([SLOW SYNC.]): Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.
DSync	Control flash timing. H([1ST CURTAIN]): The flash fires immediately after the shutter opens (generally the best choice). I([2ND CURTAIN]): The flash fires immediately before the shutter closes. R ([AUTO FP(HSS)]): High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed. Equivalent to [1ST CURTAIN] when [MULTI] is selected for flash control mode.
EZoom	The angle of illumination (flash coverage) for units that support flash zoom. Some units allow the adjustment to be made from the camera. If [AUTO] is selected, zoom will automatically be adjusted to match coverage to lens focal length.
FLighting	If the unit supports this feature, choose from: J([FLASH POWER PRIORITY]): Gain range by slightly reducing coverage. K([STANDARD]): Match coverage to picture angle. L([EVEN COVERAGE PRIORITY]): Slightly increase coverage for more even lighting.
GLED light	Choose how the built-in LED light functions during still photography (compatible units only): as a catchlight (M/[CATCHLIGHT]), as an AF-assist illuminator (N/[AF ASSIST]), or as both a catchlight and an AF-assist illuminator (O/[AF ASSIST+CATCHLIGHT]). Choose [OFF] to disable the LED during photography.
GNumber of flashes ^*	Choose the number of times the flash fires each time the shutter is released in [MULTI] mode.
HFrequency ^*	Choose the frequency at which the flash fires in [MULTI] mode.

* Full value may not be applied if limits of flash control system are exceeded.

[MASTER(OPTICAL)]

The options will be displayed if the unit is currently functioning as master flash for Fujifilm optical wireless remote flash control.

The master and remote units can be placed in up to three groups (A, B, and C) and flash mode and flash level adjusted separately for each group. Four channels are available for communication between the units; separate channels can be used for different flash systems or to prevent interference when multiple systems are operating in close proximity.

Setting	Description
AFlash control mode (group A) BFlash control mode (group B) CFlash control mode (group C)	Choose flash control modes for groups A, B, and C. [TTL%] is available for groups A and B only. [TTL]: The units in the group fire in TTL mode. Flash compensation can be adjusted separately for each group. [TTL%]: If [TTL%] is selected for either group A or B, you can specify the output of the selected group as a percentage of the other and adjust overall flash compensation for both groups. [M]: In mode [M], the units in the group fire at the selected output (expressed as a fraction of full power) regardless of subject brightness or camera settings. [MULTI]: Choosing [MULTI] for any group sets all the units in all groups to repeating flash mode. All units will fire multiple times with each shot. D: If [OFF] is selected, the units in the group will not fire.
DFlash compensation/output (group A) EFlash compensation/output (group B) FFlash compensation/output (group C)	Adjust flash level for the selected group according to option selected for flash control mode. Note that the full value may not be applied if the limits of the flash control system are exceeded. [TTL]: Adjust flash compensation. [M]/[MULTI]: Adjust flash output. [TTL%]: Choose the balance between groups A and B and adjust overall flash compensation.
GFlash mode (TTL)	Choose a flash mode for TTL flash control. The options available vary with the shooting mode ([P], [S], [A], or [M]) selected. E([FLASH AUTO]): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken. F([STANDARD]): The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released. G([SLOW SYNC.]): Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.
HSync	Control flash timing. H([1ST CURTAIN]): The flash fires immediately after the shutter opens (generally the best choice). I([2ND CURTAIN]): The flash fires immediately before the shutter closes. R ([AUTO FP(HSS)]): High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed. Equivalent to [1ST CURTAIN] when [MULTI] is selected for flash control mode.
IZoom	The angle of illumination (flash coverage) for units that support flash zoom. Some units allow the adjustment to be made from the camera. If [AUTO] is selected, zoom will automatically be adjusted to match coverage to lens focal length.
JLighting	If the unit supports this feature, choose from: J([FLASH POWER PRIORITY]): Gain range by slightly reducing coverage. K([STANDARD]): Match coverage to picture angle. L([EVEN COVERAGE PRIORITY]): Slightly increase coverage for more even lighting.
KMaster	Assign the master flash to group A ([Gr A]), B ([Gr B]), or C ([Gr C]). If [OFF] is selected, output from the master flash will be held to a level that does not affect the final picture. Available only if the unit is mounted on the camera hot shoe as a master flash for Fujifilm optical wireless remote flash control in [TTL], [TTL%], or [M] mode.
KNumber of flashes	Choose the number of times the flash fires each time the shutter is released in [MULTI] mode.
LChannel	Choose the channel used by the master flash for communication with the remote flash units. Separate channels can be used for different flash systems or to prevent interference when multiple systems are operating in close proximity.
LFrequency	Choose the frequency at which the flash fires in [MULTI] mode.