Accessories from Fujifilm
The following optional accessories are available from Fujifilm. For the latest information on the accessories available in your region, check with your local Fujifilm representative or visit “COMPATIBILITY (Accessories)”.
- Rechargeable Li-ion batteries
- NP-W126S: Additional high-capacity NP-W126S rechargeable batteries can be purchased as required.
- Battery chargers
- BC-W126S: Replacement battery chargers can be purchased as required. At +20 °C/+68 °F, the BC-W126S charges an NP-W126S in about 150 minutes.
- AC power adapters
- AC‑9V (requires CP-W126 DC coupler): Use this 100–240 V, 50/60 Hz AC power adapter for extended shooting and playback or when copying pictures to a computer.
- DC couplers
- CP-W126: For extended shooting or playback or when using the camera with a computer, use the CP-W126 to connect the camera to the AC-9V power adapter.
- Remote releases
- RR-100: Use to reduce camera shake. A third-party adapter that converts a female three-pin,φ2.5 mm connector to a male three-pin, φ3.5 mm connector is required for connection to the camera.
- Stereo microphones
- MIC-ST1: An external microphone for movie recording.
- FUJINON lenses
- XF-/XC-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount.
- FUJINON MKX-series lenses: Cinema lenses for the FUJIFILM X-mount.
- Macro extension tubes
- MCEX-11/16: Attach between the camera and the lens to shoot at high reproduction ratios.
- Teleconverters
- XF1.4X TC WR: Increases the focal length of the compatible lenses by about 1.4×.
- XF2X TC WR: Increases the focal length of the compatible lenses by about 2.0×.
- Mount adapters
- FUJIFILM M MOUNT ADAPTER: Allows the camera to be used with a wide selection of M-mount lenses.
- Body caps
- BCP-001: Cover the camera lens mount when no lens is attached.
- Shoe-mounted flash units
- EF-X500: In addition to manual and TTL flash control, this clip-on flash unit has a Guide Number of 50/164 (ISO 100, m/ft.) and supports FP (high-speed sync), allowing it to be used at shutter speeds that exceed the flash sync speed. Featuring support for the optional EF-BP1 battery pack and Fujifilm optical wireless flash control, it can be used as a commander or remote flash unit for remote wireless flash photography.
- EF-BP1: A battery pack for EF-X500 flash units. Takes up to 8 AA batteries.
- EF-X8: This compact, clip-on flash unit draws power from the camera has a Guide Number of approximately 8/26 (ISO 100, m/ft.) and can cover the angle of view of a 16 mm lens (equivalent to 24 mm in 35 mm format).
- EF-60: In addition to manual and TTL flash control, this clip-on flash unit has a Guide Number of 60/197 (ISO 100, m/ft.) and supports FP (high-speed sync), allowing it to be used at shutter speeds that exceed the flash sync speed. It can also be used as remote flash under the control of an optional EF-W1 wireless commander.
- EF-42: This clip-on flash unit has a Guide Number of 42/137 (ISO 100, m/ft.) and supports manual and TTL flash control.
- EF-X20: This clip-on flash unit has a Guide Number of 20/65 (ISO 100, m/ft.) and supports manual and TTL flash control.
- EF-20: This clip-on flash unit has a Guide Number of 20/65 (ISO 100, m/ft.) and supports TTL flash control (manual flash control is not supported).
- EF-W1: With support for the NAS * wireless communication standard developed by Nissin Japan, this wireless flash commander can be used with optional EF-60 clip-on flash units and other NAS-compliant units.
* NAS is a registered trademark of Nissin Japan Ltd.
- Leather cases
- BLC-XE4: A case made from genuine leather. Pictures can be taken and batteries and memory cards inserted or removed with the camera still in its case.
- Grip belts
- GB-001: Improves grip. Combine with a hand grip for more secure handling.
- Handgrips
- MHG-XE4: Makes the camera easier to hold. Pictures can be taken and batteries and memory cards inserted or removed with the camera still in its case.
- Thumb rests
- TR-XE4: When inserted into the camera hot shoe, the thumb rest improves your grip and prevents unintended operation of camera controls.
- instax SHARE printers
- SP‑1/SP‑2/SP-3: Connect via wireless LAN to print pictures on instax film.