This website uses cookies. By using the site you are agreeing to our Privacy Policy.

Enter a search term and click .

[SET-UP 1] (G)

Adjust basic camera settings.

To access basic camera settings, press [MENU/OK] and select tab G.

F [DATE/TIME]

Set the camera clock:

  1. Select F[DATE/TIME] in the G ([SET-UP 1]) tab.

  2. Press the selector left or right to highlight the year, month, day, hour, or minute and press up or down to change.

  3. Press [MENU/OK] to set the clock.

N [TIME DIFFERENCE]

Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between your local and home time zone:

  1. Highlight g[LOCAL] and press [MENU/OK].

  2. Use the selector to choose the time difference between local time and your home time zone. Press [MENU/OK] when settings are complete.

To set the camera clock to local time, highlight g[LOCAL] and press [MENU/OK]. To set the clock to the time in your home time zone, select h[HOME]. If g[LOCAL] is selected, g will be displayed in yellow for about three seconds when the camera is turned on.

Options
g[LOCAL] h[HOME]

Qa

Choose a language.

  1. Select Qa in the G ([SET-UP 1]) tab.

  2. Highlight the desired option and press [MENU/OK].

R [RESET]

Reset shooting or setup menu options to default values.

  1. Highlight the desired option and press [MENU/OK].

    Option Description
    [SHOOTING MENU RESET] Reset all shooting menu settings other than custom white balance to default values.
    [SET-UP RESET] Reset all setup menu settings other than F[DATE/TIME], N[TIME DIFFERENCE], and r[CONNECTION SETTING] to default values.

  2. A confirmation dialog will be displayed; highlight [OK] and press [MENU/OK].

o SOUND & FLASH

Select [OFF] to disable the speaker, flash, and illuminator in situations in which camera sounds or lights may be unwelcome.

Options
[ON] [OFF]

o appears in the display when [OFF] is selected.

b SOUND SET-UP

Adjust sound settings.

[OPERATION VOL.]

Adjust the volume of the sounds produced when camera controls are operated. Choose f to disable control sounds.

Options
b (high) c (medium) d (low) f (mute)

[SHUTTER VOLUME]

Adjust the volume of the sounds produced by the electronic shutter. Choose f to disable the shutter sound.

Options
b (high) c (medium) d (low) f (mute)

[SHUTTER SOUND]

Choose the sound made by the electronic shutter.

Options
i[SOUND 1] j[SOUND 2] k[SOUND 3]

[PLAYBACK VOLUME]

Adjust the volume for movie playback. Choose from 10 options between 10 (high) and 1 (low) or select 0 to mute audio during movie playback.

Options
10 9 8 7 6 5 4 3 2 1 0

A SCREEN SET-UP

Adjust display settings.

[IMAGE DISP.]

Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mottling may be visible at high sensitivities. Note that at some settings, the camera will display pictures after shooting regardless of the option selected.

Option Description
[CONTINUOUS] Pictures are displayed until the [MENU/OK] button is pressed or the shutter button is pressed halfway. To zoom in on the active focus point, press the center of the sub-command dial; press again to cancel zoom.
[1.5 SEC] Pictures are displayed for the selected time or until the shutter button is pressed halfway.
[0.5 SEC]
[OFF] Pictures are not displayed after shooting.

PREVIEW EXP. IN MANUAL MODE

Select [ON] to enable exposure preview in manual exposure mode.

Options
[ON] [OFF]

Select [OFF] when using the flash or on other occasions on which exposure may change when the picture is taken.

[LCD BRIGHTNESS]

Adjust monitor brightness.

Options
+5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5

[LCD COLOR]

Adjust monitor hue.

Options
+5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5

[PREVIEW PIC. EFFECT]

Choose [ON] to preview the effects of film simulation, white balance, and other settings in the monitor, [OFF] to make shadows in low-contrast, back-lit scenes and other hard-to-see subjects more visible.

Options
[ON] [OFF]

If [OFF] is selected, the effects of camera settings will not be visible in the monitor and colors and tone will differ from those in the final picture. The display will however be adjusted to show the effects of advanced filters and of monochrome and sepia settings.

[FRAMING GUIDELINE]

Choose a framing grid for shooting mode.

  Option
F[GRID 9] G[GRID 24] H[HD FRAMING]
Display
For “rule of thirds” composition. A six-by-four grid. Frame HD pictures in the crop shown by the lines at the top and bottom of the display.

Framing guides are not shown at default settings but can be displayed using A[SCREEN SET-UP] > [DISP. CUSTOM SETTING] (a [DISP. CUSTOM SETTING]).

[AUTOROTATE PB]

Choose [ON] to automatically rotate “tall” (portrait-orientation) pictures during playback.

Options
[ON] [OFF]

[FOCUS CHECK]

If [ON] is selected, the display will automatically zoom in on the selected focus area when the focus ring is rotated in manual focus mode.

Options
[ON] [OFF]

Pressing the center of the sub-command dial cancels focus zoom.

[FOCUS SCALE UNITS]

Choose the units used for the focus distance indicator.

Options
[METERS] [FEET]

[DISP. CUSTOM SETTING]

Choose the items shown in the standard display.

  1. In shooting mode, use the [DISP/BACK] button to display standard indicators.

  2. Press [MENU/OK] and select A[SCREEN SET-UP] > [DISP. CUSTOM SETTING] in the setup menu.

  3. Highlight items and press [MENU/OK] to select or deselect.

    Item Default
    [FRAMING GUIDELINE] w
    [ELECTRONIC LEVEL] w
    [FOCUS FRAME] R
    [AF DISTANCE INDICATOR] w
    [MF DISTANCE INDICATOR] R
    [HISTOGRAM] w
    [SHOOTING MODE] R
    [APERTURE/S-SPEED/ISO] R
    [INFORMATION BACKGROUND] R
    [Expo. Comp. (Digit)] w
    [Expo. Comp. (Scale)] R
    [FOCUS MODE] R
    [PHOTOMETRY] R
    [SHUTTER TYPE] R
    [FLASH] R
    [CONTINUOUS MODE] R
    [DUAL IS MODE] R
    [WHITE BALANCE] R
    [FILM SIMULATION] R
    [DYNAMIC RANGE] R
    [FRAMES REMAINING] R
    [IMAGE SIZE/QUALITY] R
    [MOVIE MODE & REC. TIME] R
    [AUTO IMAGE TRANSFER] R
    [BATTERY LEVEL] R

  4. Press [DISP/BACK] to save changes.

  5. Press [DISP/BACK] as needed to exit the menus and return to the shooting display.