.[SET UP]
Adjust camera settings.
Qa
Choose a language.
[DATE/TIME]
Set the date and time.
[HOME LOCATION]
Choose your time zone from a map.
Press [ON/OFF] (Screen button 6) to enable or disable daylight saving time.
[DATE/TIME]
Set the camera clock.
[TIME DIFFERENCE]
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling.
| Option | Description |
|---|---|
| [HOME] | Set the camera clock to your home time zone. |
| [LOCAL] | Set the camera clock to the local time at your travel destination. |
Use [LOCAL AREA] to choose your home time zone before selecting a local time zone using [LOCAL].
[LOCAL AREA]
Choose the region of your travel destination from a map.
[RESET ALL EXCEPT NETWORK SETTINGS]
Reset settings other than [NETWORK] and custom white balance to default values.
Press two [RESET] (Screen buttons 4 and 6) simultaneously to reset.
[FORMAT]
Select and format a memory card or USB-connected SSD.
| Options | ||
|---|---|---|
| [SLOT1] | [SLOT2] | [SSD] |
Select the media and press two [FORMAT] (Screen buttons 4 and 6) simultaneously to start formatting.
[MAINTENANCE]
Perform sensor maintenance and check the condition of the supplied battery.
[PIXEL MAPPING]
Use this option to reduce bright spots if you notice them in your movie.
Results are not guaranteed.
Be sure the battery is fully charged.
Pixel mapping is not available when the camera temperature is elevated.
Processing may take several tens of seconds.
[SENSOR CLEANING]
Remove dust from the camera image sensor.
| Option | Description |
|---|---|
| [UPDATE NOW] | Clean the sensor immediately. |
| [CLEAN TIMING] | Sensor cleaning will be performed when the camera is turned on or off. |
Even after performing sensor cleaning, dust cannot be completely removed from the camera image sensor.
If the dust cannot be removed, contact your Fujifilm dealer.
[BATTERY AGE]
Check the battery age for the supplied battery. Age is expressed as a number between 0 and 4. The higher the number, the older the supplied battery.
The older the supplied battery, the faster it loses its charge. We recommend that you purchase a new battery.
[COOLING FAN SETTING]
Set the camera’s cooling fan.
[COOLING FAN]
Adjust settings for the cooling fan.
| Option | Description |
|---|---|
| [AUTO1] | The fan turns on automatically as required when camera temperature rises and runs at slow speed. |
| [AUTO2] | The fan turns on and automatically operates from low speed to high speed in order when camera temperature rises. The increased fan noise may be audible in movies. |
| [LOW] | Run the fan continuously at low speed. |
| [HIGH] | Run the fan continuously at high speed. The increased fan noise may be audible in movies. |
[HIGH MODE SETTING]
Adjust the fan speed when the fan runs at high speed.
[LOW MODE SETTING]
Adjust the fan speed when the fan runs at slow speed.
[REC MODE SETTING]
Set whether to stop the cooling fan operation when starting movie recording.
| Options | |
|---|---|
| [CONTINUE] | [STOP] |
When [STOP] is selected, the fan runs at high speed automatically during standby.
[POWER MANAGEMENT]
Set the camera’s power supply.
[V Battery Low Warning %]
Set the battery level at which the V-mount battery low-level warning is displayed. The level can be set 0% to 100% in 1% increments.
This setting is only valid when using a battery that displays the remaining battery level as a percentage.
[V Battery Low Warning V]
Set the battery voltage at which the V-mount battery low-level warning is displayed. The voltage can be set from 11.5 V to 17.0 V in 0.1 V increments.
This setting is not valid when using a battery that displays the remaining battery level as a percentage.
[LED/SOUND SETTING]
[TALLY LIGHT SETTING]
Set whether to light [REC] during movie recording. Select [ON] to light the button.
| Option | Description |
|---|---|
| [FRONT] | Set whether to light [REC] on the front. |
| [SIDE] | Set whether to light [REC] on the side. |
[REC START BEEP]
Choose the volume at the start and end of movie recording.
| Options | |||
|---|---|---|---|
| b (high) | c (medium) | d (low) | f (mute) |
[LCD SETTING]
Configure the display settings for the LCD monitor and the side monitors.
[LCD BRIGHTNESS]
Adjust the brightness of the display in the LCD monitor.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
[LCD COLOR]
Adjust the saturation of the display in the LCD monitor.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
[LCD COLOR ADJUSTMENT]
Adjust the color of the display in the LCD monitor. Adjust the color of the display on two axes, the R axis and the B axis.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
[SIDE MONITOR BRIGHTNESS]
Adjust the brightness of the display in the side monitors.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
[SIDE MONITOR COLOR]
Adjust the background color of the side monitors.
| Options | |
|---|---|
| [LIGHT] | [DARK] |
[FIRMWARE UPDATE]
Update the firmware (aFirmware Updates).
[BODY]
Update the firmware of the camera body.
[LENS]
Update the firmware of the lens attached to the camera.
[LCD MONITOR]
Update the firmware of the LCD monitor.
[MOUNT ADAPTER]
Update the firmware of the mount adapter.
[REGULATORY]
Select [SET UP] > [REGULATORY] in the setup menu to view electronic copies of the product model number, FCC/ISED regulatory information, and other certificates.
